2022 Valid HPE2-T37 Real Exam Questions (Updated) 100% Dumps & Practice Exam
[UPDATED 2022] HP HPE2-T37 Questions Prepare with Free Demo of PDF
NEW QUESTION 14
Click the option that must be configured for an HPE OneView when an HPE storage system is connected directly to an HPE Synergy frame.
Answer:
Explanation:
NEW QUESTION 15
You want to put two FlexNlCs into a single Link Aggregation Group within a server profile. What Is a prerequisite for this setup?
- A. An upgrade license must be purchased and deployed.
- B. Both FlexNlCs must be connected to the same network.
- C. The Compute Module profile must have exactly two connections defined.
- D. The sFlow option must be enabled and configured.
Answer: D
NEW QUESTION 16
Your customer wants to use HPE OneView for VMware vCenter Server to simplify management of their VMware cluster running on HPE Synergy. The customer is concerned with the cost of additional licenses.
How will you explain licensing rules for this product?
- A. If the number of the HPE Synergy Compute Modules installed in HPE Synergy frame is less than 10, no license is required to use HPE OneView tor VMware vCenter Server.
- B. As long as the customer has HPE OneVtew Global Dashboard deployed, HPE OneView for VMware vCenter Server does not require any additional licenses.
- C. One HPE OneView for VMware vCenter Server license is required per HPE Synergy frame if more than
10 Compute Modules are installed in the frame. - D. As long as the server is managed using HPE OneView. the customer can use HPE OneView for VMware vCenter Server without additional licenses.
Answer: C
NEW QUESTION 17
Which parameters can be defined in a server profile template for HPE Synergy Compute Modules? (Select two.)
- A. IL0 IPv4 or IPv6 address.
- B. partition layout for servers running Linux.
- C. NIC teaming setup at OS level.
- D. local storage and BIOS settings.
- E. network and storage connectivity.
Answer: D,E
NEW QUESTION 18
For HPE Primera, match each task with the management tool that can be used to perform it.
Answer:
Explanation:
NEW QUESTION 19
Refer to the exhibit.
You discovered that one of the profiles is not compliant with the server profile template. What could cause this profile to be inconsistent with the server profile template?
- A. The server was powered off or rebooted recently and IL0 did not reconnect to HPE OneView.
- B. Changes to the server profile were implemented directly on the server profile.
- C. Network connectivity for HPE Synergy Compute Module was changed outside HPE OneView.
- D. HPE OneView was restored from a backup that created ^consistency with the server profile template.
Answer: C
NEW QUESTION 20
You want to update the firmware for only two HPE Synergy Virtual Connect SE 32Gb FC Modules of a large environment. From which level must this procedure be initiated?
- A. Logical Interconnect Group
- B. Logical Interconnect
- C. Server Profile
- D. Logical Enclosure
Answer: D
NEW QUESTION 21
What is the best practice when deploying an HPE OneView appliance?
- A. Deploy two HPE OneView appliances and configure them in HA mode.
- B. Use thin-provisioning for the HPE OneView appliance to save storage capacity.
- C. Enable VMware Fault Tolerance if the appliance is deployed to a VMware hypervisor.
- D. deploy the appliance in a hypervisor cluster that Is not managed by OneView.
Answer: D
NEW QUESTION 22
Refer to the exhibit.
Your customer created multiple networks in HPE OneView, but only Eth-1 is available to be used within a server profile. What is a likely cause of this situation?
- A. The other networks are not added to the Logical Interconnect Group configuration.
- B. The other networks are not configured with the required Smart Link parameter.
- C. The other networks have Private Network' selected, which hides them from Compute Modules.
- D. The other networks are configured with a purpose other than General or Management.
Answer: C
NEW QUESTION 23
Which statement about an HPE OneView server profile is true?
- A. A server profile can be used to update firmware and drivers when the operating system on the server is up and running.
- B. A server profile created for a specific server hardware type cannot be moved to a server with a different server hardware type.
- C. A server profile can be used to configure a local storage controller, but cannot be used to configure SAN-based storage.
- D. A server profile can be created only for HPE BladeSystem, HPE Synergy, and HPE Superdome Flex servers.
Answer: C
NEW QUESTION 24
You try to add an HPE Primera array to HPE OneView, but you get a connectivity error. However, you can connect to the array using SSMC. What should you verify before adding HPE Primera to HPE OneView?
- A. whether array management using HPE OneView is enabled in SSMC.
- B. whether there are at least two Fibre Channel networks defined in HPE OneView.
- C. whether WSAPI service is enabled on HPE Primera array.
- D. whether the appropriate license for HPE Primera Is available in HPE OneView.
Answer: C
NEW QUESTION 25
Which types of support dump can be created using HPE OneView? (Select two.)
- A. Logical enclosure support dump
- B. Firmware deployment support dump
- C. Enclosure group support dump
- D. Maintenance console support dump
- E. Appliance support dump
Answer: A,D
NEW QUESTION 26
You want to add the latest IL0 firmware to an HPE OneView firmware repository. How can you complete this task?
- A. A custom SPP iso Image must be created with the new IL0 firmware version and uploaded to the repository.
- B. A PowerShell script must be used to upload IL0 firmware to the Internal or external firmware repository.
- C. An external repository must be created, because standalone components are supported only In an external repository.
- D. ILO firmware can be marked as a hotnx and uploaded directly to the Internal or external firmware repository.
Answer: C
NEW QUESTION 27
Your customer added HPE Primera to HPE OneVlew and enabled volume provisioning on all storage pools.
For security reasons, the customer wants to disable volume provisioning using HPE OneView on a specific storage pool.
How can this task be completed?
- A. The storage pool should be disabled using the array management tool.
- B. The storage pool should be removed from HPE OneView using a PowerShell script.
- C. The storage pool state should be changed to discovered using HPE OneView.
- D. The storage pool should be marked as read-only using HPE OneView.
Answer: A
NEW QUESTION 28
You configured downlink aggregation for one of the HPE Synergy Compute Modules in an environment by placing two connections in the same Link Aggregation Group. After you made the changes to the server profile, its status changed to critical.
What can be done to fix this issue?
- A. Link Aggregation Group functionality should be enabled in advanced properties of the Logical Interconnect.
- B. Ensure that the Link Aggregation Group time-out value matches the server set values.
- C. The server profile for a given HPE Synergy compute module should be reapplied, then the Compute Module should be rebooted.
- D. The teaming or bonding driver in the server OS must be configured to enable the LACP and to form the LAG correctly.
Answer: A
NEW QUESTION 29
Which statement about M-LAG setup is true?
- A. M-LAG for HPE Synergy can be either single-homed or multi-homed, while for HPE BladeSystem only single-homed.
- B. When combined with IRF, M-LAG will allow you to aggregate ports coming from clustered HPE Synergy Virtual Connect modules.
- C. M-LAG has to be defined manually for HPE BladeSystem, but it is automatically configured for HPE Synergy.
- D. sFLOW cannot be enabled if M-LAG is configured between HPE Synergy Virtual Connect modules in the same frame.
Answer: B
NEW QUESTION 30
......
HPE2-T37 Deluxe Study Guide with Online Test Engine: https://examcollection.actualcollection.com/HPE2-T37-exam-questions.html