[Jan-2024] The Best CWAP Wi-Fi Analysis Study Guide for the CWAP-404 Exam
CWAP-404 certification guide Q&A from Training Expert ActualCollection
CWNP CWAP-404 Exam Certification Details:
| Duration | 90 minutes |
| Number of Questions | 60 |
| Exam Registration | PEARSON VUE |
| Exam Code | CWAP-404 CWAP |
| Passing Score | 70% |
| Recommended Training | CWAP self-paced training kit, Training Class |
| Sample Questions | CWNP CWAP-404 Sample Questions |
NEW QUESTION # 35
ABC International has installed a new smart ZigBee controlled lighting system. However, the network team is concerned that this new system will interfere with the existing WLAN and has asked you to investigate the impact of the two systems operating simultaneously in the 2.4 GHz band. When performing Spectrum Analysis, which question could you answer by looking at the FFT plot?
- A. Do the ZigBee channels used by the lighting system overlap with the WLAN channels?
- B. Is the WLAN corrupting ZigBee system messages?
- C. Is the ZigBee system causing an increase in WLAN retries?
- D. Is the ZigBee system using more than 50% of the available airtime?
Answer: A
Explanation:
Explanation
The FFT plot is a spectrum analysis plot that shows the RF power present at a particular frequency over a short period of time. It can help identify the sources and characteristics of RF signals in the spectrum. By looking at the FFT plot, you can determine which ZigBee channels are used by the lighting system and whether they overlap with the WLAN channels in the 2.4 GHz band. ZigBee channels are 5 MHz wide and WLAN channels are 20 MHz or 40 MHz wide, so there is a possibility of overlap and interference between them. The other questions cannot be answered by looking at the FFT plot alone, as they require other types of plots or analysis tools, such as duty cycle plot, airtime utilization plot, or protocol analyzer. References: [Wireless Analysis Professional Study Guide], Chapter 3: Spectrum Analysis, page 69-70
NEW QUESTION # 36
You are troubleshooting a client that is experiencing slow WLAN performance. As part of the troubleshooting activity, you start a packet capture on your laptop close to the client device. While analyzing the packets, you suspect that you have not captured all packets transmitted by the client. By analyzing the trace file, how can you confirm if you have missing packets?
- A. Protocol Analyzers show the number of missing packets in their statistics view
- B. Look for gaps in the sequence number in MAC headers.
- C. The missing packets will be shown as CRC errored packets
- D. Retransmission are an indication of missing packets
Answer: B
Explanation:
Explanation
One way to confirm if you have missing packets in your packet capture is to look for gaps in the sequence number in MAC headers. The sequence number is a 12-bit field in the MAC header that is used to identify and order data frames within a traffic stream. The sequence number is incremented by one for each new data frame transmitted by a STA, except for retransmissions, fragments, and control frames. The sequence number can range from 0 to 4095, and then wraps around to 0. If you see a jump or a gap in the sequence number between two consecutive data frames from the same STA, it means that you have missed some packets in between. The other options are not correct, as they do not confirm if you have missing packets in your packet capture. CRC errored packets are packets that have been corrupted during transmission and have failed the error detection check. Protocol analyzers may show the number of CRC errored packets in their statistics view, but not the number of missing packets. Retransmissions are an indication of packet loss or collision, but not necessarily of missing packets in your capture. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 5: 802.11 MAC Sublayer, page 114-115
NEW QUESTION # 37
What interframe space would be expected between a CIS and a Data frame?
- A. DIFS
- B. AIFS
- C. PIFS
- D. SIFS
Answer: D
Explanation:
Explanation
The interframe space that would be expected between a CTS (Clear to Send) and a Data frame is SIFS (Short Interframe Space). A SIFS is the shortest interframe space that is used for high-priority transmissions, such as ACKs (Acknowledgements), CTSs, or data frames that are part of a fragmentation or aggregation process. A SIFS is a fixed value that depends on the PHY type and channel width. A CTS and a Data frame are part of a virtual carrier sense mechanism called RTS/CTS (Request to Send/Clear to Send), which is used to avoid collisions and hidden node problems in wireless transmissions. When a STA (station) wants to send a data frame, it first sends an RTS frame to the intended receiver, indicating the duration of the transmission. The receiver then responds with a CTS frame, also indicating the duration of the transmission. The other STAs in the vicinity hear either the RTS or the CTS frame and update their NAV (Network Allocation Vector) timers accordingly, deferring their access to the medium until the transmission is over. The sender then sends the data frame after waiting for a SIFS, followed by an ACK frame from the receiver after another SIFS. The other options are not correct, as they are not used between a CTS and a Data frame. A PIFS (PCF Interframe Space) is used for medium access by the PCF (Point Coordination Function), which is an optional and rarely implemented polling-based mechanism that provides contention-free service for time-sensitive traffic. An AIFS (Arbitration Interframe Space) is used for medium access by different ACs (Access Categories), which are logical queues that correspond to different QoS (Quality of Service) levels for different types of traffic. An AIFS is a variable interframe space that depends on the AIFSN (Arbitration Interframe Space Number) value of each AC. A DIFS (Distributed Interframe Space) is used for medium access by the DCF (Distributed Coordination Function), which is the default and mandatory contention-based mechanism that provides best-effort service for normal traffic. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 6: 802.11 Frame Exchanges, page 166-167; Chapter 7: QoS Analysis, page 194-195
NEW QUESTION # 38
How many frames are exchanged for 802.11 authentication in the 6 GHz band when WPA3-Enterprise is not used, and a passphrase is used instead?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: B
Explanation:
Explanation
Two frames are exchanged for 802.11 authentication in the 6 GHz band when WPA3-Enterprise is not used, and a passphrase is used instead. Authentication is a process that establishes an identity relationship between a STA (station) and an AP (access point) before joining a BSS (Basic Service Set). There are two types of authentication methods defined by 802.11: Open System Authentication and Shared Key Authentication. Open System Authentication does not require any credentials or security information from a STA to join a BSS, and it consists of two frames: an Authentication Request frame sent by the STA to the AP, and an Authentication Response frame sent by the AP to the STA. Shared Key Authentication requires a shared secret key from a STA to join a BSS, and it consists of four frames: two challenge-response frames in addition to the request-response frames. However, Shared Key Authentication uses WEP (Wired Equivalent Privacy) as its encryption algorithm, which is insecure and deprecated. In the 6 GHz band, which is a newly available frequency band for WLANs, Shared Key Authentication is prohibited by the 802.11 standard, as it poses security and interference risks for other users and services in the band. The 6 GHz band requires all WLANs to use WPA3-Personal or WPA3-Enterprise encryption methods, which are more secure and robust than previous encryption methods such as WPA2 or WEP. WPA3-Personal uses a passphrase to derive a PMK (Pairwise Master Key), while WPA3-Enterprise uses an authentication server to obtain a PMK. Both methods use SAE (Simultaneous Authentication of Equals) as their authentication protocol, which replaces PSK (Pre-Shared Key) or EAP (Extensible Authentication Protocol). SAE consists of two frames: an SAE Commit frame sent by both parties to exchange elliptic curve parameters and nonces, and an SAE Confirm frame sent by both parties to verify each other's identities and generate a PMK. Therefore, when WPA3-Enterprise is not used, and a passphrase is used instead in the 6 GHz band, only two frames are exchanged for 802.11 authentication:
an SAECommit frame and an SAE Confirm frame. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 8: Security Analysis, page 220-221
NEW QUESTION # 39
Which one of the these is the most important in the WLAN troubleshooting methodology among those listed?
- A. Obtain detailed -knowledge of the wireless vendors debug and logging options
- B. Talk to the end users about their experiences
- C. Observe the problem
- D. Interview the network manager about the issues being experienced
Answer: C
Explanation:
Explanation
Observing the problem is the most important step in the WLAN troubleshooting methodology among those listed. This step involves capturing and analyzing the relevant data from the wireless network, such as packets, frames, spectrum, and performance metrics. Observing the problem helps to verify the existence and scope of the issue, identify the root cause and possible solutions, and validate the results of any actions taken. The other steps are also important, but they are not as critical as observing the problem12 References:
CWAP-404 Study Guide, Chapter 1: Troubleshooting Methodology, page 15
CWAP-404 Objectives, Section 1.2: Observe the problem
NEW QUESTION # 40
In what scenario is Open Authentication without encryption not allowed based on the 802.11 standard?
- A. When operating a BS5 in the CBRS band
- B. When operating a BSS in FIPS mode
- C. When operating a BSS in the 6 GHz band
- D. When operating a BSS in a government facility
Answer: C
Explanation:
Explanation
Open Authentication without encryption is not allowed when operating a BSS in the 6 GHz band, according to the 802.11 standard. Open Authentication is a type of authentication method that does not require any credentials or security information from a STA (station) to join a BSS (Basic Service Set). Open Authentication can be used with or without encryption, depending on the configuration of the BSS and the STA. Encryption is a technique that scrambles the data frames using an algorithm and a key to prevent unauthorized access or eavesdropping. However, in the 6 GHz band, which is a newly available frequency band for WLANs, OpenAuthentication without encryption is prohibited by the 802.11 standard, as it poses security and interference risks for other users and services in the band. The 6 GHz band requires all WLANs to use WPA3-Personal or WPA3-Enterprise encryption methods, which are more secure and robust than previous encryption methods such as WPA2 or WEP. The other options are not correct, as they do not describe scenarios where Open Authentication without encryption is not allowed by the 802.11 standard. When operating a BSS in the CBRS band, which is another newly available frequency band for WLANs, Open Authentication without encryption is allowed, but not recommended, as it also poses security and interference risks for other users and services in the band. When operating a BSS in FIPS mode, which is a mode that complies with the Federal Information Processing Standards for cryptographic security, Open Authentication without encryption is allowed, but not compliant, as it does not meet the FIPS requirements for encryption algorithms and keys. When operating a BSS in a government facility, Open Authentication without encryption is allowed, but not advisable, as it may violate the government policies or regulations for wireless security. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 8: Security Analysis, page 220-221
NEW QUESTION # 41
In a Spectrum Analyzer the Swept Spectrogram plot displays what information?
- A. The RF time domain
- B. Reductions in frame transmissions
- C. Wi-Fi Device information
- D. RF power present at a particular frequency over the course of time
Answer: D
Explanation:
Explanation
The Swept Spectrogram plot is a spectrum analysis plot that shows the RF power present at a particular frequency over the course of time. It can help identify trends and patterns in the RF spectrum over a longer period of time. It can also show how the RF environment changes over time and how different sources of RF signals affect each other. The other options are not correct, as they describe different types of plots or information that are not related to the Swept Spectrogram plot. References: [Wireless Analysis Professional Study Guide], Chapter 3: Spectrum Analysis, page 72-73
NEW QUESTION # 42
The PHY layer provides framing by adding a header to create what type of data unit?
- A. PPDU
- B. MPDU
- C. PSDU
- D. MSDU
Answer: A
Explanation:
Explanation
The PHY layer provides framing by adding a header to create a PPDU. A PPDU (PHY Protocol Data Unit) is the data unit that is transmitted or received over the wireless medium by the PHY layer. A PPDU consists of a PSDU (PHY Service Data Unit) and a PHY header, which contains information such as modulation, coding, and data rate. The PHY layer adds the PHY header to the PSDU to create a PPDU for transmission, or removes the PHY header from the PPDU to extract the PSDU for reception. The other options are not correct, as they are not created by adding a header at the PHY layer. An MPDU (MAC Protocol Data Unit) is created by adding a MAC header and FCS to an MSDU (MAC Service Data Unit) at the MAC layer. An MSDU is the data unit that is passed from the LLC sublayer to the MAC sublayer or vice versa. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 4: 802.11 Physical Layer, page 97-98
NEW QUESTION # 43
What should the To DS and From DS flags be to set to in an Association Response frame?
- A. To DS - 1, From DS = 0
- B. To DS = 1, From DS = 1
- C. To DS - 0, From DS = 0
- D. To DS = 0, From DS = 1
Answer: C
Explanation:
Explanation
The To DS and From DS flags should be set to 0 in an Association Response frame. An Association Response frame is a type of management frame that is transmitted by an AP to accept or reject an association request from a STA. The To DS (To Distribution System) and From DS (From Distribution System) flags are two bits in the Frame Control field of the MAC header that indicate whether a frame is destined for or originated from the DS (Distribution System), which is a system that connects multiple BSSs together. The To DS and From DS flags can have four possible combinations: 00, 01, 10, or 11. For an Association Response frame, which is sent from an AP to a STA within a BSS, both flags should be set to 0. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 5: 802.11 MAC Sublayer, page 121-122
NEW QUESTION # 44
You are performing a multiple adapter channel aggregation capture to troubleshoot a VoIP roaming problem and would like to measure the roaming time from the last VoIP packet sent on the old AP's channel to the first VoIP packet sent on the new AP's channel. Which timing column in the packet view would measure this for you?
- A. Relative
- B. Delta
- C. Absolute
- D. Roaming
Answer: B
Explanation:
Explanation
Delta is the timing column in the packet view that measures the time difference between two consecutive packets in a capture file. Delta can be used to measure the roaming time from the last VoIP packet sent on the old AP's channel to the first VoIP packet sent on the new AP's channel by selecting these two packets and looking at their delta values. The other timing columns are not suitable for this measurement because they do not show the time difference between two specific packets. Roaming is a column that shows whether a packet belongs to a roaming event or not. Relative is a column that shows the time elapsed since the beginning of the capture file. Absolute is a column that shows the date and time when a packet was captured5 References:
CWAP-404 Study Guide, Chapter 2: Protocol Analysis, page 57
CWAP-404 Objectives, Section 2.4: Analyze timing values
NEW QUESTION # 45
What is encrypted within the third message of the 4-Way Handshake?
- A. GTK
- B. PMK
- C. PTK
- D. GMK
Answer: A
Explanation:
Explanation
The GTK (Group Temporal Key) is encrypted within the third message of the 4-Way Handshake. The 4-Way Handshake is a process that establishes a secure connection between a STA (station) and an AP (access point) using WPA2 (Wi-Fi Protected Access 2), which is a security protocol that uses AES-CCMP (Advanced Encryption Standard-Counter Mode CBC-MAC Protocol) as its encryption algorithm. The 4-Way Handshake consists of four messages that are exchanged between the STA and the AP. The first message is sent by the AP to the STA, containing the ANonce (Authenticator Nonce), which is a random number generated by the AP.
The second message is sent by the STA to the AP, containing the SNonce (Supplicant Nonce), which is a random number generated by the STA, and the MIC (Message Integrity Code), which is a value that verifies the integrity of the message. The third message is sent by the AP to the STA, containing the GTK, which is a key that is used to encrypt and decrypt multicast and broadcast data frames, and the MIC. The GTK is encrypted with the KEK (Key Encryption Key), which is derived from the PTK (Pairwise Temporal Key). The PTK is a key that is used to encrypt and decrypt unicast data frames, and it is derived from the PMK (Pairwise Master Key), the ANonce, and the SNonce. The fourth message is sent by the STA to the AP, containing only the MIC, to confirm the completion of the 4-Way Handshake. The other options are not correct, asthey are not encrypted within the third message of the 4-Way Handshake. The PMK is a key that is derived from a passphrase or obtained from an authentication server, and it is not transmitted in any message of the 4-Way Handshake. The PTK is a key that is derived from the PMK, the ANonce, and the SNonce, and it is not transmitted in any message of the 4-Way Handshake. The GMK (Group Master Key) is a key that is generated by the AP and used to derive the GTK, and it is not transmitted in any message of the 4-Way Handshake. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 8: Security Analysis, page 211-213
NEW QUESTION # 46
During a VHT Transmit Beamforming sounding exchange, the beamformee transmits a Compressed Beamforming frame to the beamformer. What is communicated within this Compressed Beamforming frame?
- A. Beamformee Matrix
- B. Feedback Matrix
- C. Beamforming Matrix
- D. Steering Matrix
Answer: B
Explanation:
Explanation
The beamformee transmits a Feedback Matrix within the Compressed Beamforming frame to the beamformer.
The Feedback Matrix contains information about the channel state between the beamformee and each spatial stream of the beamformer. This information is used by the beamformer to adjust its transmit weights and optimize its signal for the beamformee34. References: CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 11: 802.11n/ac/ax PHYsical Layer Frame Exchanges, page 4033; CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 11: 802.11n/ac/ax PHYsical Layer Frame Exchanges, page 4064.
NEW QUESTION # 47
Which one of the following is required for Wi-Fi integration in laptop-based Spectrum Analyzer software in addition to the spectrum analysis adapter?
- A. A directional antenna
- B. An 802.11 wireless adaptor
- C. A firmware upgrade for the spectrum analysis adapter
- D. SNMP read credentials to the WLAN controller or APs
Answer: B
Explanation:
Explanation
An 802.11 wireless adaptor is required for Wi-Fi integration in laptop-based spectrum analyzer software in addition to the spectrum analysis adapter. The spectrum analysis adapter is a hardware device that captures the RF signals in the wireless environment and sends them to the spectrum analyzer software for analysis and display. The 802.11 wireless adapter is a hardware device that connects the laptop to the wireless network and allows the spectrum analyzer software to correlate the RF data with the Wi-Fi data, such as SSID, channel, and BSSID. This enables the spectrum analyzer software to provide more context and insight into the spectrum activity and its impact on the Wi-Fi network. A firmware upgrade for the spectrum analysis adapter is not required for Wi-Fi integration, but it may be needed to fix bugs or add features to the device. A directional antenna is an antenna that focuses the RF energy in a specific direction and has a high gain and a narrow beamwidth. A directional antenna can be used with a spectrum analysis adapter to pinpoint the location or source of interference or noise in the wireless environment, but it is not required for Wi-Fi integration. SNMP read credentials to the WLAN controller or APs are not required for Wi-Fi integration, but they may be useful for obtaining additional information about the wireless network configuration and performance from the network devices.References:
CWAP-404 Study Guide, Chapter 4: Spectrum Analysis and Troubleshooting, page 123 CWAP-404 Objectives, Section 4.2: Integrate Wi-Fi data with spectrum analysis data CWAP-404 Study Guide, Chapter 4: Spectrum Analysis and Troubleshooting, page 131
NEW QUESTION # 48
Which one of the following is an advantage of using display filters that is not an advantage of capture-time filters?
- A. Once created they are reusable for later captures
- B. They only hide the packets from view and the filtered packets can be enabled for view later
- C. Multiple of them can be applied simultaneously
- D. They allow for focused analysis on just the packets of interest
Answer: B
Explanation:
Explanation
Display filters are applied after the capture is completed and they only hide the packets from view. The filtered packets are still present in the capture file and can be enabled for view later by changing or removing the display filter. This is an advantage over capture-time filters, which discard the packets that do not match the filter criteria and cannot be recovered later34 References:
CWAP-403 Study Guide, Chapter 2: Protocol Analysis, page 37
CWAP-403 Objectives, Section 2.3: Apply display filters
NEW QUESTION # 49
In which element of a Beacon frame would you look to identity the current HT protection mode in which an AP is operating?
- A. ERP Information Element
- B. HT Operations Element
- C. HT Protection Element
- D. HT Capabilities Element
Answer: B
Explanation:
Explanation
The HT protection mode in which an AP is operating can be identified by looking at the HT Operations element in a Beacon frame. The HT Operations element is a part of the Beacon frame that contains information about the High Throughput (HT) capabilities and operation of an 802.11n BSS. The HT Operations element has a field called HT Protection, which indicates how the BSS protects its HT transmissions from interference or collisions with non-HT devices or BSSs. The HT Protection field can have four values: No Protection, Nonmember Protection, 20 MHz Protection, or Non-HT Mixed Mode. The other options are not correct, as they do not contain information about the HT protection mode. The HT Protection element does not exist, the ERP Information element is used for Extended Rate PHY (ERP) protection mode for 802.11g devices, and the HT Capabilities element is used for indicating the supported HT features of an individual device. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 5: 802.11 MAC Sublayer, page 125-126
NEW QUESTION # 50
An RTS frame should be acknowledged by which frame?
- A. Ack
- B. Block Ack
- C. CTS
- D. RTS-Ack
Answer: C
Explanation:
Explanation
An RTS (Request to Send) frame should be acknowledged by a CTS (Clear to Send) frame. An RTS and CTS frame are types of control frames that are used to implement a virtual carrier sense mechanism called RTS/CTS. RTS/CTS is a technique that helps to avoid collisions and hidden node problems in wireless transmissions. When a STA (station) wants to send a data frame, it first sends an RTS frame to the intended receiver, indicating the duration of the transmission. The receiver then responds with a CTS frame, also indicating the duration of the transmission. The other STAs in the vicinity hear either the RTS or the CTS frame and update their NAV (Network Allocation Vector) timers accordingly, deferring their access to the medium until the transmission is over. The sender then sends the data frame, followed by an ACK (Acknowledgement) frame from the receiver. The other options are not correct, as they are not used to acknowledge an RTS frame. An ACK frame is used to acknowledge a data frame, not an RTS frame. An RTS-Ack frame does not exist, as there is no such type of control frame in 802.11. A Block Ack (BA) frame is used to acknowledge multiple data frames in a single frame, not an RTS frame. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 6: 802.11 Frame Exchanges, page 166-167
NEW QUESTION # 51
......
The Best CWNP CWAP-404 Study Guides and Dumps of 2024: https://examcollection.actualcollection.com/CWAP-404-exam-questions.html